Difference between revisions of "Category:Wireless Space"
From NAS-Central Lacie Wiki
m (Added links) |
|||
(4 intermediate revisions by the same user not shown) | |||
Line 87: | Line 87: | ||
31 1 3072 mtdblock1 | 31 1 3072 mtdblock1 | ||
31 2 4096 mtdblock2 | 31 2 4096 mtdblock2 | ||
− | 31 3 122880 mtdblock3 | + | 31 3 122880 mtdblock3 - about 120MB and contains orginal firmware backup in my case 1.0.2 |
=== cat /proc/mounts === | === cat /proc/mounts === | ||
Line 139: | Line 139: | ||
mtd2: 00400000 00020000 "uInitrd_m" | mtd2: 00400000 00020000 "uInitrd_m" | ||
mtd3: 07800000 00020000 "root" | mtd3: 07800000 00020000 "root" | ||
+ | |||
+ | |||
+ | |||
+ | == Serial console output with firmware 1.1.4 == | ||
+ | <pre> | ||
+ | _ ____ _ | ||
+ | | | __ _ / ___(_) ___ | ||
+ | | | / _` | | | |/ _ \ | ||
+ | | |___ (_| | |___| | __/ | ||
+ | |_____\__,_|\____|_|\___| | ||
+ | _ _ ____ _ | ||
+ | | | | | | __ ) ___ ___ | |_ | ||
+ | | | | |___| _ \ / _ \ / _ \| __| | ||
+ | | |_| |___| |_) | (_) | (_) | |_ | ||
+ | \___/ |____/ \___/ \___/ \__| | ||
+ | ** MARVELL BOARD: ASTON_WS_GN3 LE | ||
+ | Hold rear button - long : FAIL | ||
+ | |||
+ | |||
+ | U-Boot 1.1.4 (Feb 11 2010 - 11:04:03) Marvell version: 3.4.16 LaCie 1.4.2 256MB | ||
+ | |||
+ | U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CE5E0 | ||
+ | |||
+ | Soc: MV88F6281 Rev 3 (DDR2) | ||
+ | CPU running @ 800Mhz L2 running @ 400Mhz | ||
+ | SysClock = 200Mhz , TClock = 166Mhz | ||
+ | |||
+ | DRAM CAS Latency = 6 tRP = 3 tRAS = 9 tRCD=3 | ||
+ | DRAM CS[0] base 0x00000000 size 256MB | ||
+ | DRAM Total size 256MB 16bit width | ||
+ | Flash: 0 kB | ||
+ | Addresses 8M - 0M are saved for the U-Boot usage. | ||
+ | Mem malloc Initialization (8M - 7M): Done | ||
+ | NAND:128 MB | ||
+ | |||
+ | CPU : Marvell Feroceon (Rev 1) | ||
+ | |||
+ | Streaming disabled | ||
+ | Write allocate disabled | ||
+ | |||
+ | Module 0 is MII | ||
+ | |||
+ | USB 0: host mode | ||
+ | PCI 0: PCI Express Root Complex Interface | ||
+ | PEX interface detected Link X1 | ||
+ | Net: egiga0 [PRIME], egiga1 | ||
+ | Waiting for LUMP (3) | ||
+ | no lump receive; continuing | ||
+ | Hit any key to stop autoboot: 0 | ||
+ | |||
+ | Reset IDE: | ||
+ | Marvell Serial ATA Adapter | ||
+ | Integrated Sata device found | ||
+ | [0 0 0]: Enable DMA mode | ||
+ | Device 0 @ 0 0: | ||
+ | Model: SAMSUNG HD103SI Firm: 1AG01118 Ser#: ---removed--- | ||
+ | Type: Hard Disk | ||
+ | Supports 48-bit addressing | ||
+ | Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) | ||
+ | |||
+ | ## Valid EFI partition found ## | ||
+ | ## Valid EFI partition found ## | ||
+ | |||
+ | 2440768 bytes read | ||
+ | |||
+ | ## Checking Image at 00800000 ... | ||
+ | Image Name: Linux-2.6.22.18 | ||
+ | Created: 2011-08-29 11:01:29 UTC | ||
+ | Image Type: ARM Linux Kernel Image (uncompressed) | ||
+ | Data Size: 2440704 Bytes = 2.3 MB | ||
+ | Load Address: 00008000 | ||
+ | Entry Point: 00008000 | ||
+ | Verifying Checksum ... OK | ||
+ | Kernel IDE success | ||
+ | ## Valid EFI partition found ## | ||
+ | ## Valid EFI partition found ## | ||
+ | |||
+ | 3215424 bytes read | ||
+ | |||
+ | ## Checking Image at 01200000 ... | ||
+ | Image Name: 8M_ramdisk | ||
+ | Created: 2011-08-29 11:32:42 UTC | ||
+ | Image Type: ARM Linux RAMDisk Image (uncompressed) | ||
+ | Data Size: 3215360 Bytes = 3.1 MB | ||
+ | Load Address: 01200000 | ||
+ | Entry Point: 01200000 | ||
+ | Verifying Checksum ... OK | ||
+ | IinitRD IDE success | ||
+ | ## Booting image at 00800000 ... | ||
+ | Image Name: Linux-2.6.22.18 | ||
+ | Created: 2011-08-29 11:01:29 UTC | ||
+ | Image Type: ARM Linux Kernel Image (uncompressed) | ||
+ | Data Size: 2440704 Bytes = 2.3 MB | ||
+ | Load Address: 00008000 | ||
+ | Entry Point: 00008000 | ||
+ | Verifying Checksum ... OK | ||
+ | OK | ||
+ | ## Loading Ramdisk Image at 01200000 ... | ||
+ | Image Name: 8M_ramdisk | ||
+ | Created: 2011-08-29 11:32:42 UTC | ||
+ | Image Type: ARM Linux RAMDisk Image (uncompressed) | ||
+ | Data Size: 3215360 Bytes = 3.1 MB | ||
+ | Load Address: 01200000 | ||
+ | Entry Point: 01200000 | ||
+ | Verifying Checksum ... OK | ||
+ | |||
+ | Starting kernel ... | ||
+ | |||
+ | Uncompressing Linux.......................................................................................................................................................... done, booting the kernel. | ||
+ | Linux version 2.6.22.18 (root@ws32.lacie.com) (gcc version 4.2.1) #1 Mon Aug 29 11:01:15 UTC 2011 | ||
+ | CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 | ||
+ | Machine: wireless_space | ||
+ | Using UBoot passing parameters structure | ||
+ | Memory policy: ECC disabled, Data cache writeback | ||
+ | CPU0: D VIVT write-back cache | ||
+ | CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets | ||
+ | CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets | ||
+ | Built 1 zonelists. Total pages: 65024 | ||
+ | Kernel command line: initrd=0x1200000 root=/dev/mtdblock3 ro console=ttyS0,115200 | ||
+ | PID hash table entries: 1024 (order: 10, 4096 bytes) | ||
+ | Console: colour dummy device 80x30 | ||
+ | Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) | ||
+ | Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) | ||
+ | Memory: 256MB 0MB 0MB 0MB = 256MB total | ||
+ | Memory: 251648KB available (4504K code, 300K data, 144K init) | ||
+ | Mount-cache hash table entries: 512 | ||
+ | CPU: Testing write buffer coherency: ok | ||
+ | NET: Registered protocol family 16 | ||
+ | |||
+ | CPU Interface | ||
+ | ------------- | ||
+ | SDRAM_CS0 ....base 00000000, size 256MB | ||
+ | SDRAM_CS1 ....disable | ||
+ | SDRAM_CS2 ....disable | ||
+ | SDRAM_CS3 ....disable | ||
+ | PEX0_MEM ....base e8000000, size 128MB | ||
+ | PEX0_IO ....base f2000000, size 1MB | ||
+ | INTER_REGS ....base f1000000, size 1MB | ||
+ | NFLASH_CS ....base fa000000, size 2MB | ||
+ | SPI_CS ....base f4000000, size 16MB | ||
+ | BOOT_ROM_CS ....no such | ||
+ | DEV_BOOTCS ....no such | ||
+ | CRYPT_ENG ....base f0000000, size 2MB | ||
+ | |||
+ | Marvell Development Board (LSP Version KW_LSP_4.2.7_patch2)-- wireless_space Soc: MV88F6281 Rev 3 LE | ||
+ | |||
+ | Detected Tclk 166666667 and SysClk 200000000 | ||
+ | MV Buttons Device Load | ||
+ | Register Marvell USB EHCI Host controller #0 | ||
+ | PEX0 interface detected Link X1 | ||
+ | PCI: bus0: Fast back to back transfers disabled | ||
+ | SCSI subsystem initialized | ||
+ | usbcore: registered new interface driver usbfs | ||
+ | usbcore: registered new interface driver hub | ||
+ | usbcore: registered new device driver usb | ||
+ | NET: Registered protocol family 2 | ||
+ | Time: kw_clocksource clocksource has been installed. | ||
+ | IP route cache hash table entries: 2048 (order: 1, 8192 bytes) | ||
+ | TCP established hash table entries: 8192 (order: 4, 65536 bytes) | ||
+ | TCP bind hash table entries: 8192 (order: 3, 32768 bytes) | ||
+ | TCP: Hash tables configured (established 8192 bind 8192) | ||
+ | TCP reno registered | ||
+ | checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd | ||
+ | Freeing initrd memory: 3140K | ||
+ | Use the XOR engines (acceleration) for enhancing the following functions: | ||
+ | o RAID 5 Xor calculation | ||
+ | o kernel memcpy | ||
+ | o kenrel memzero | ||
+ | Number of XOR engines to use: 2 | ||
+ | cesadev_init(c00118ac) | ||
+ | mvCesaInit: sessions=640, queue=64, pSram=f0000000 | ||
+ | MV Buttons Driver Load | ||
+ | mv_rtc mv_rtc: rtc core: registered mv_rtc as rtc0 | ||
+ | mv_rtc mv_rtc: Kirkwood SoC RTC added | ||
+ | Init kirkwood cpufreq driver | ||
+ | gpio-fan gpio-fan: GPIO fan initialized | ||
+ | gpio-hd-power gpio-hd-power: GPIO Hard Disk power device initialized | ||
+ | gpio-usb gpio-usb: GPIO USB mode switch is not available | ||
+ | gpio-usb gpio-usb: GPIO USB device VBUS is not available | ||
+ | gpio-usb gpio-usb: USB GPIO's initialized | ||
+ | Registered led device: ws:red:front | ||
+ | Registered led device: ws:green:front | ||
+ | Registered led device: ws:blue:front | ||
+ | squashfs: version 3.3 (2007/10/31) Phillip Lougher | ||
+ | squashfs: LZMA suppport for slax.org by jro | ||
+ | NTFS driver 2.1.28 [Flags: R/O]. | ||
+ | JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. | ||
+ | fuse init (API version 7.8) | ||
+ | SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled | ||
+ | io scheduler noop registered | ||
+ | io scheduler anticipatory registered (default) | ||
+ | Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled | ||
+ | serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A | ||
+ | serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A | ||
+ | RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize | ||
+ | INIT Marvell Ethernet Driver: mv_netdev | ||
+ | Loading Marvell Ethernet Driver: | ||
+ | o Cached descriptors in DRAM | ||
+ | o DRAM SW cache-coherency | ||
+ | o Single RX Queue support - ETH_DEF_RXQ=0 | ||
+ | o Single TX Queue support - ETH_DEF_TXQ=0 | ||
+ | o TCP segmentation offload enabled | ||
+ | o Receive checksum offload enabled | ||
+ | o Transmit checksum offload enabled | ||
+ | o Network Fast Processing (Routing) supported | ||
+ | o Driver ERROR statistics enabled | ||
+ | o Driver INFO statistics enabled | ||
+ | o Driver DEBUG statistics enabled | ||
+ | o Proc tool API enabled | ||
+ | o Gateway support enabled | ||
+ | o Using Marvell Header Mode | ||
+ | o L2 IGMP support | ||
+ | o Rx descripors: q0=128 | ||
+ | o Tx descripors: q0=532 | ||
+ | o Loading network interface(s): | ||
+ | o eth0, ifindex = 1, GbE port = 1 | ||
+ | o Loading Gateway interface(s): | ||
+ | o Using default network configuration, overriding boot MAC address | ||
+ | o MTU set to 1500. | ||
+ | o mac_addr 00:00:00:00:00:00, VID 0x100, port list: port-0 port-1 port-2 | ||
+ | o eth1, ifindex = 2, GbE port = 0 | ||
+ | |||
+ | mvFpRuleDb (cfdae000): 2048 entries, 8192 bytes | ||
+ | e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI | ||
+ | e100: Copyright(c) 1999-2006 Intel Corporation | ||
+ | PPP generic driver version 2.4.2 | ||
+ | PPP Deflate Compression module registered | ||
+ | PPP BSD Compression module registered | ||
+ | PPP MPPE Compression module registered | ||
+ | NET: Registered protocol family 24 | ||
+ | Integrated Sata device found | ||
+ | scsi0 : Marvell SCSI to SATA adapter | ||
+ | scsi1 : Marvell SCSI to SATA adapter | ||
+ | scsi 0:0:0:0: Direct-Access SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5 | ||
+ | Disk topology: host_no=0 channel=0 id=0 | ||
+ | sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) | ||
+ | sd 0:0:0:0: [sda] Write Protect is off | ||
+ | sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA | ||
+ | sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) | ||
+ | sd 0:0:0:0: [sda] Write Protect is off | ||
+ | sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA | ||
+ | sda: sda1 sda2 sda3 sda4 | ||
+ | sd 0:0:0:0: [sda] Attached SCSI disk | ||
+ | sd 0:0:0:0: Attached scsi generic sg0 type 0 | ||
+ | NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ | ||
+ | NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit) | ||
+ | Scanning device for bad blocks | ||
+ | Bad eraseblock 112 at 0x00e00000 | ||
+ | Using static partition definition | ||
+ | Creating 4 MTD partitions on "nand_mtd": | ||
+ | 0x00000000-0x00100000 : "u-boot" | ||
+ | 0x00100000-0x00400000 : "uImage" | ||
+ | 0x00400000-0x00800000 : "uInitrd_m" | ||
+ | 0x00800000-0x08000000 : "root" | ||
+ | ehci_marvell ehci_marvell.70059: Marvell Orion EHCI | ||
+ | ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 | ||
+ | ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 | ||
+ | ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 | ||
+ | usb usb1: configuration #1 chosen from 1 choice | ||
+ | hub 1-0:1.0: USB hub found | ||
+ | hub 1-0:1.0: 1 port detected | ||
+ | usb 1-1: new high speed USB device using ehci_marvell and address 2 | ||
+ | usb 1-1: configuration #1 chosen from 1 choice | ||
+ | hub 1-1:1.0: USB hub found | ||
+ | hub 1-1:1.0: 3 ports detected | ||
+ | usbcore: registered new interface driver usblp | ||
+ | /home/emmanuel/workspace/wirelessspace-RC/components/kernel/source/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver | ||
+ | Initializing USB Mass Storage driver... | ||
+ | usbcore: registered new interface driver usb-storage | ||
+ | USB Mass Storage support registered. | ||
+ | mice: PS/2 mouse device common for all mice | ||
+ | input: gpio-keys as /class/input/input0 | ||
+ | i2c /dev entries driver | ||
+ | at24 0-0050: 512 byte 24c04 EEPROM (writable) | ||
+ | md: linear personality registered for level -1 | ||
+ | md: raid0 personality registered for level 0 | ||
+ | md: raid1 personality registered for level 1 | ||
+ | raid6: int32x1 73 MB/s | ||
+ | raid6: int32x2 80 MB/s | ||
+ | raid6: int32x4 83 MB/s | ||
+ | raid6: int32x8 75 MB/s | ||
+ | raid6: using algorithm int32x4 (83 MB/s) | ||
+ | md: raid6 personality registered for level 6 | ||
+ | md: raid5 personality registered for level 5 | ||
+ | md: raid4 personality registered for level 4 | ||
+ | raid5: measuring checksumming speed | ||
+ | arm4regs : 726.400 MB/sec | ||
+ | 8regs : 505.600 MB/sec | ||
+ | 32regs : 603.200 MB/sec | ||
+ | raid5: using function: arm4regs (726.400 MB/sec) | ||
+ | device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com | ||
+ | dm_crypt using the OCF package. | ||
+ | u32 classifier | ||
+ | Performance counters on | ||
+ | Netfilter messages via NETLINK v0.30. | ||
+ | nf_conntrack version 0.5.0 (2048 buckets, 16384 max) | ||
+ | ctnetlink v0.93: registering with nfnetlink. | ||
+ | ip_tables: (C) 2000-2006 Netfilter Core Team | ||
+ | arp_tables: (C) 2002 David S. Miller | ||
+ | TCP cubic registered | ||
+ | NET: Registered protocol family 1 | ||
+ | NET: Registered protocol family 17 | ||
+ | 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> | ||
+ | All bugs added by David S. Miller <davem@redhat.com> | ||
+ | mv_rtc mv_rtc: setting the system clock to 2012-09-24 17:13:24 (1348506804) | ||
+ | md: Autodetecting RAID arrays. | ||
+ | md: autorun ... | ||
+ | md: ... autorun DONE. | ||
+ | RAMDISK: squashfs filesystem found at block 0 | ||
+ | RAMDISK: Loading 3139KiB [1 disk] into ram disk... done. | ||
+ | VFS: Mounted root (squashfs filesystem) readonly. | ||
+ | date seems valid: 2012-09-24 17:13:24 | ||
+ | * Mounting base stuff * | ||
+ | kjournald starting. Commit interval 5 seconds | ||
+ | EXT3-fs warning: maximal mount count reached, running e2fsck is recommended | ||
+ | EXT3 FS on sda1, internal journal | ||
+ | EXT3-fs: mounted filesystem with ordered data mode. | ||
+ | * copyCheck is not there, checking bootcheck* | ||
+ | * Bootcheck not there , everything is fine * | ||
+ | Hdd seems sane... | ||
+ | *Checking if a new firmware is there | ||
+ | * Mount /proc... | ||
+ | * Mount /tmp... | ||
+ | * Create /tmp/sda4... | ||
+ | * Mount /dev/sda4... | ||
+ | XFS mounting filesystem sda4 | ||
+ | * Unmount all... | ||
+ | * Done. | ||
+ | <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< | ||
+ | No update found, boot from HDD... | ||
+ | <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< | ||
+ | start flashing blue led | ||
+ | pivoting | ||
+ | *Done* | ||
+ | kjournald starting. Commit interval 5 seconds | ||
+ | EXT3-fs: mounted filesystem with ordered data mode. | ||
+ | VFS: Mounted root (ext3 filesystem) readonly. | ||
+ | Trying to move old root to /initrd ... okay | ||
+ | Freeing init memory: 144K | ||
+ | INIT: version 2.86 booting | ||
+ | Unmount old /proc | ||
+ | Unmount old /initrd | ||
+ | Mounting tmp /etc... | ||
+ | Populate /etc... | ||
+ | Mounting all... | ||
+ | Mounting /dev/sda3 on /lacie/var | ||
+ | kjournald starting. Commit interval 5 seconds | ||
+ | EXT3-fs warning: maximal mount count reached, running e2fsck is recommended | ||
+ | EXT3 FS on sda3, internal journal | ||
+ | EXT3-fs: recovery complete. | ||
+ | EXT3-fs: mounted filesystem with ordered data mode. | ||
+ | Mounting /dev/sda4 on /lacie/var/userPart | ||
+ | FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! | ||
+ | FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! | ||
+ | XFS mounting filesystem sda4 | ||
+ | Creating new /var into hdd... | ||
+ | EXT3-fs warning: maximal mount count reached, running e2fsck is recommended | ||
+ | EXT3 FS on sda1, internal journal | ||
+ | Adding 249992k swap on /dev/sda2. Priority:-1 extents:1 across:249992k | ||
+ | Populating /var... | ||
+ | Done. | ||
+ | INIT: Entering runlevel: 2 | ||
+ | [Lo] mounting loopback interface | ||
+ | ** Checking shares ** | ||
+ | rmdir: '/lacie/share/inne': Directory not empty | ||
+ | rmdir: '/lacie/share/media': Not a directory | ||
+ | rmdir: '/lacie/share/transmission_web': Directory not empty | ||
+ | ** Shares checked ** | ||
+ | [udevd] starting kernel event manager | ||
+ | udev: starting version 139 | ||
+ | [udevd] loading hardware drivers | ||
+ | ** hwClock ** | ||
+ | Set system date from RTC HW clock | ||
+ | Mon Sep 24 19:13:29 CEST 2012 | ||
+ | [klaxon] starting | ||
+ | [klaxon] running from HDD | ||
+ | eth0: started | ||
+ | eth0: stopped | ||
+ | mv_gateway: starting eth1 | ||
+ | mv_gateway: stopping eth1 | ||
+ | rt3090sta: module license 'unspecified' taints kernel. | ||
+ | |||
+ | |||
+ | === pAd = d08d1000, size = 507432 === | ||
+ | |||
+ | <-- RTMPAllocAdapterBlock, Status=0 | ||
+ | pAd->CSRBaseAddress =0xd08c0000, csr_addr=0xd08c0000! | ||
+ | RX DESC ff019000 size = 2048 | ||
+ | <-- RTMPAllocTxRxRingMemory, Status=0 | ||
+ | Key1Str is Invalid key length(0) or Type(0) | ||
+ | Key2Str is Invalid key length(0) or Type(0) | ||
+ | Key3Str is Invalid key length(0) or Type(0) | ||
+ | Key4Str is Invalid key length(0) or Type(0) | ||
+ | 1. Phy Mode = 9 | ||
+ | 2. Phy Mode = 9 | ||
+ | NVM is Efuse and its size =2d[2d0-2fc] | ||
+ | RTMPSetPhyMode: channel is out of range, use first channel=1 | ||
+ | Read EEPROM, EthCloneMac is ---mac---! | ||
+ | 3. Phy Mode = 9 | ||
+ | MCS Set = ff ff 00 00 01 | ||
+ | <==== rt28xx_init, Status=0 | ||
+ | 0x1300 = 00064300 | ||
+ | AUX_CTRL = 0x c02 | ||
+ | Read AUX_CTRL = 0xc02 | ||
+ | Write AUX_CTRL = 0x1c02 | ||
+ | OSC_CTRL = 0x3ff11 | ||
+ | ====> rt30xx Read PowerLevelMode = 0x3. | ||
+ | ====> rt30xx F Write 0x83 Command = 0x3. | ||
+ | mv_gateway: eth1 change mac address to --mac-- | ||
+ | mv_gateway: starting eth1 | ||
+ | device eth1 entered promiscuous mode | ||
+ | acm_msg> ACM_MEM_Alloc_Num = 1 | ||
+ | acm_msg> ACM_MEM_Free_Num = 1 | ||
+ | rt28xx_close call RT28xxPciAsicRadioOff fail !! | ||
+ | device ra0 entered promiscuous mode | ||
+ | RX DESC ff019000 size = 2048 | ||
+ | <-- RTMPAllocTxRxRingMemory, Status=0 | ||
+ | CfgSetCountryRegion():CountryRegion in eeprom was programmed | ||
+ | CfgSetCountryRegion():CountryRegion in eeprom was programmed | ||
+ | Key1Str is Invalid key length(0) or Type(0) | ||
+ | Key2Str is Invalid key length(0) or Type(0) | ||
+ | Key3Str is Invalid key length(0) or Type(0) | ||
+ | Key4Str is Invalid key length(0) or Type(0) | ||
+ | 1. Phy Mode = 9 | ||
+ | 2. Phy Mode = 9 | ||
+ | NVM is Efuse and its size =2d[2d0-2fc] | ||
+ | RTMPSetPhyMode: channel is out of range, use first channel=1 | ||
+ | 3. Phy Mode = 9 | ||
+ | MCS Set = ff ff 00 00 01 | ||
+ | <==== rt28xx_init, Status=0 | ||
+ | 0x1300 = 00064300 | ||
+ | AUX_CTRL = 0x 1d42 | ||
+ | Read AUX_CTRL = 0x1d42 | ||
+ | Write AUX_CTRL = 0x1d42 | ||
+ | OSC_CTRL = 0x3ff11 | ||
+ | ====> rt30xx Read PowerLevelMode = 0x3. | ||
+ | ====> rt30xx F Write 0x83 Command = 0x3. | ||
+ | br_wan: port 2(ra0) entering learning state | ||
+ | br_wan: port 1(eth1) entering learning state | ||
+ | br_wan: topology change detected, propagating | ||
+ | br_wan: port 2(ra0) entering forwarding state | ||
+ | br_wan: topology change detected, propagating | ||
+ | br_wan: port 1(eth1) entering forwarding state | ||
+ | eth0: mac address changed | ||
+ | eth0: started | ||
+ | WARNING: at /home/emmanuel/workspace/wirelessspace-RC/components/kernel/source/kernel/softirq.c:138 local_bh_enable() | ||
+ | [<c0116890>] (dump_stack+0x0/0x14) from [<c0163974>] (local_bh_enable+0x40/0xb0) | ||
+ | [<c0163934>] (local_bh_enable+0x0/0xb0) from [<bf0bd1c8>] (RtmpAsicSendCommandToMcu+0x114/0x4d0 [rt3090sta]) | ||
+ | r5:d08d1000 r4:000b0100 | ||
+ | [<bf0bd0b4>] (RtmpAsicSendCommandToMcu+0x0/0x4d0 [rt3090sta]) from [<bf03e024>] (AsicSendCommandToMcu+0x28/0x34 [rt3090sta]) | ||
+ | [<bf03dffc>] (AsicSendCommandToMcu+0x0/0x34 [rt3090sta]) from [<bf04910c>] (AsicAdjustTxPower+0x2b8/0x1c80 [rt3090sta]) | ||
+ | [<bf048e54>] (AsicAdjustTxPower+0x0/0x1c80 [rt3090sta]) from [<bf00e6f4>] (STAMlmePeriodicExec+0x3c8/0xda4 [rt3090sta]) | ||
+ | [<bf00e32c>] (STAMlmePeriodicExec+0x0/0xda4 [rt3090sta]) from [<bf00f668>] (MlmePeriodicExec+0x598/0x734 [rt3090sta]) | ||
+ | [<bf00f0d0>] (MlmePeriodicExec+0x0/0x734 [rt3090sta]) from [<bf039b34>] (rtmp_timer_MlmePeriodicExec+0x24/0x40 [rt3090sta]) | ||
+ | r6:bf039b10 r5:00000100 r4:d08e9e9c | ||
+ | [<bf039b10>] (rtmp_timer_MlmePeriodicExec+0x0/0x40 [rt3090sta]) from [<c016731c>] (run_timer_softirq+0x150/0x1e8) | ||
+ | r5:00000100 r4:c04c4d40 | ||
+ | [<c01671cc>] (run_timer_softirq+0x0/0x1e8) from [<c01636c0>] (__do_softirq+0x74/0xec) | ||
+ | r7:123196a6 r6:00000002 r5:c04c4ae8 r4:00000001 | ||
+ | [<c016364c>] (__do_softirq+0x0/0xec) from [<c0163a94>] (irq_exit+0x48/0x50) | ||
+ | r7:123196a6 r6:00000000 r5:c049eb50 r4:00000001 | ||
+ | [<c0163a4c>] (irq_exit+0x0/0x50) from [<c002c048>] (__exception_text_start+0x48/0x60) | ||
+ | [<c002c000>] (__exception_text_start+0x0/0x60) from [<c002c564>] (__irq_usr+0x44/0xa0) | ||
+ | Exception stack(0xce78ffb0 to 0xce78fff8) | ||
+ | ffa0: 36363636 36363636 6e0740b3 1e3111a6 | ||
+ | ffc0: 36363636 7c36d615 36363636 123196a6 36363636 f22fe673 50307191 beb22764 | ||
+ | ffe0: 5a827999 beb225e0 fc8bf99c 0005df48 00000010 ffffffff | ||
+ | r7:123196a6 r6:0000001e r5:f1020200 r4:ffffffff | ||
+ | ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 130 | ||
+ | ==>rt_ioctl_siwfreq::SIOCSIWFREQ[cmd=0x8b04] (Channel=1) | ||
+ | Rcv Wcid(1) AddBAReq | ||
+ | Start Seq = 00000000 | ||
+ | Syslogd Started | ||
+ | [thumbd] Starting application | ||
+ | Segmentation fault | ||
+ | using old certificate | ||
+ | Starting setup server | ||
+ | setup is disabled | ||
+ | * bootcheck * | ||
+ | |||
+ | wshd login: >> smart_spindown start - disk(s): sda | ||
+ | |||
+ | wshd login: | ||
+ | </pre> |
Latest revision as of 21:12, 24 September 2012
Wireless Space | |
CPU | SoC Marvell 88F6281 |
RAM | 256MB |
Flash ROM | 128MB |
Other | |
NIC | |
USB | |
internal HDD | Samsung HD103SI on 1TB version |
SATA Controller | |
Drive Capacity | 1TB or 2TB |
Fan | |
Kernel | 2.6.22.18 |
Contents
Links
Firmware updates: http://www.lacie.com/support/support_manifest.htm?id=10520 GPL source code: http://www.lacie.com/gpl SoC data sheets: http://www.marvell.com/products/processors/embedded/kirkwood lacie-nas project: http://lacie-nas.org
uname -a
Linux WirelessSpace 2.6.22.18 #1 Fri Aug 20 09:20:02 CEST 2010 armv5tejl unknown
cat /proc/cpuinfo
Processor : ARM926EJ-S rev 1 (v5l) BogoMIPS : 799.53 Features : swp half thumb fastmult edsp CPU implementer : 0x56 CPU architecture: 5TE CPU variant : 0x2 CPU part : 0x131 CPU revision : 1 Cache type : write-back Cache clean : cp15 c7 ops Cache lockdown : format C Cache format : Harvard I size : 16384 I assoc : 4 I line length : 32 I sets : 128 D size : 16384 D assoc : 4 D line length : 32 D sets : 128 Hardware : wireless_space Revision : 0000 Serial : 0000000000000000
cat /proc/meminfo
MemTotal: 254988 kB MemFree: 3684 kB Buffers: 8716 kB Cached: 212236 kB SwapCached: 88 kB Active: 108072 kB Inactive: 122700 kB SwapTotal: 249992 kB SwapFree: 249436 kB Dirty: 456 kB Writeback: 0 kB AnonPages: 9760 kB Mapped: 12136 kB Slab: 15556 kB SReclaimable: 1920 kB SUnreclaim: 13636 kB PageTables: 724 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 377484 kB Committed_AS: 124728 kB VmallocTotal: 385024 kB VmallocUsed: 1316 kB VmallocChunk: 383692 kB
cat /proc/partitions
major minor #blocks name 8 0 976762584 sda 8 1 292952 sda1 8 2 250000 sda2 8 3 97656 sda3 8 4 976121942 sda4 31 0 1024 mtdblock0 31 1 3072 mtdblock1 31 2 4096 mtdblock2 31 3 122880 mtdblock3 - about 120MB and contains orginal firmware backup in my case 1.0.2
cat /proc/mounts
rootfs / rootfs rw 0 0 /dev/root / ext3 ro,noatime,data=ordered 0 0 tmpfs /etc tmpfs rw 0 0 none /proc proc rw 0 0 none /sys sysfs rw 0 0 tmpfs /tmp tmpfs rw 0 0 /dev/sda3 /lacie/var ext3 rw,noatime,data=ordered 0 0 /dev/sda4 /lacie/var/userPart xfs rw,noatime 0 0 usbfs /proc/bus/usb usbfs rw 0 0 /dev/root /dev/.static/dev ext3 ro,noatime,data=ordered 0 0 udev /dev tmpfs rw 0 0
cat /proc/filesystems
nodev sysfs nodev rootfs nodev bdev nodev proc nodev debugfs nodev sockfs nodev usbfs nodev pipefs nodev anon_inodefs nodev futexfs nodev tmpfs nodev inotifyfs nodev devpts ext3 ext2 squashfs nodev ramfs msdos vfat hfsplus nodev nfs ntfs jffs2 nodev fuse fuseblk nodev fusectl xfs nodev rpc_pipefs tntfs
cat /proc/mtd
dev: size erasesize name mtd0: 00100000 00020000 "u-boot" mtd1: 00300000 00020000 "uImage" mtd2: 00400000 00020000 "uInitrd_m" mtd3: 07800000 00020000 "root"
Serial console output with firmware 1.1.4
_ ____ _ | | __ _ / ___(_) ___ | | / _` | | | |/ _ \ | |___ (_| | |___| | __/ |_____\__,_|\____|_|\___| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: ASTON_WS_GN3 LE Hold rear button - long : FAIL U-Boot 1.1.4 (Feb 11 2010 - 11:04:03) Marvell version: 3.4.16 LaCie 1.4.2 256MB U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CE5E0 Soc: MV88F6281 Rev 3 (DDR2) CPU running @ 800Mhz L2 running @ 400Mhz SysClock = 200Mhz , TClock = 166Mhz DRAM CAS Latency = 6 tRP = 3 tRAS = 9 tRCD=3 DRAM CS[0] base 0x00000000 size 256MB DRAM Total size 256MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:128 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled Module 0 is MII USB 0: host mode PCI 0: PCI Express Root Complex Interface PEX interface detected Link X1 Net: egiga0 [PRIME], egiga1 Waiting for LUMP (3) no lump receive; continuing Hit any key to stop autoboot: 0 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found [0 0 0]: Enable DMA mode Device 0 @ 0 0: Model: SAMSUNG HD103SI Firm: 1AG01118 Ser#: ---removed--- Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) ## Valid EFI partition found ## ## Valid EFI partition found ## 2440768 bytes read ## Checking Image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2011-08-29 11:01:29 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2440704 Bytes = 2.3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Kernel IDE success ## Valid EFI partition found ## ## Valid EFI partition found ## 3215424 bytes read ## Checking Image at 01200000 ... Image Name: 8M_ramdisk Created: 2011-08-29 11:32:42 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 3215360 Bytes = 3.1 MB Load Address: 01200000 Entry Point: 01200000 Verifying Checksum ... OK IinitRD IDE success ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2011-08-29 11:01:29 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2440704 Bytes = 2.3 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 01200000 ... Image Name: 8M_ramdisk Created: 2011-08-29 11:32:42 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 3215360 Bytes = 3.1 MB Load Address: 01200000 Entry Point: 01200000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux.......................................................................................................................................................... done, booting the kernel. Linux version 2.6.22.18 (root@ws32.lacie.com) (gcc version 4.2.1) #1 Mon Aug 29 11:01:15 UTC 2011 CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 Machine: wireless_space Using UBoot passing parameters structure Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Built 1 zonelists. Total pages: 65024 Kernel command line: initrd=0x1200000 root=/dev/mtdblock3 ro console=ttyS0,115200 PID hash table entries: 1024 (order: 10, 4096 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 256MB 0MB 0MB 0MB = 256MB total Memory: 251648KB available (4504K code, 300K data, 144K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 256MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e8000000, size 128MB PEX0_IO ....base f2000000, size 1MB INTER_REGS ....base f1000000, size 1MB NFLASH_CS ....base fa000000, size 2MB SPI_CS ....base f4000000, size 16MB BOOT_ROM_CS ....no such DEV_BOOTCS ....no such CRYPT_ENG ....base f0000000, size 2MB Marvell Development Board (LSP Version KW_LSP_4.2.7_patch2)-- wireless_space Soc: MV88F6281 Rev 3 LE Detected Tclk 166666667 and SysClk 200000000 MV Buttons Device Load Register Marvell USB EHCI Host controller #0 PEX0 interface detected Link X1 PCI: bus0: Fast back to back transfers disabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 Time: kw_clocksource clocksource has been installed. IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd Freeing initrd memory: 3140K Use the XOR engines (acceleration) for enhancing the following functions: o RAID 5 Xor calculation o kernel memcpy o kenrel memzero Number of XOR engines to use: 2 cesadev_init(c00118ac) mvCesaInit: sessions=640, queue=64, pSram=f0000000 MV Buttons Driver Load mv_rtc mv_rtc: rtc core: registered mv_rtc as rtc0 mv_rtc mv_rtc: Kirkwood SoC RTC added Init kirkwood cpufreq driver gpio-fan gpio-fan: GPIO fan initialized gpio-hd-power gpio-hd-power: GPIO Hard Disk power device initialized gpio-usb gpio-usb: GPIO USB mode switch is not available gpio-usb gpio-usb: GPIO USB device VBUS is not available gpio-usb gpio-usb: USB GPIO's initialized Registered led device: ws:red:front Registered led device: ws:green:front Registered led device: ws:blue:front squashfs: version 3.3 (2007/10/31) Phillip Lougher squashfs: LZMA suppport for slax.org by jro NTFS driver 2.1.28 [Flags: R/O]. JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.8) SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled io scheduler noop registered io scheduler anticipatory registered (default) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize INIT Marvell Ethernet Driver: mv_netdev Loading Marvell Ethernet Driver: o Cached descriptors in DRAM o DRAM SW cache-coherency o Single RX Queue support - ETH_DEF_RXQ=0 o Single TX Queue support - ETH_DEF_TXQ=0 o TCP segmentation offload enabled o Receive checksum offload enabled o Transmit checksum offload enabled o Network Fast Processing (Routing) supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Driver DEBUG statistics enabled o Proc tool API enabled o Gateway support enabled o Using Marvell Header Mode o L2 IGMP support o Rx descripors: q0=128 o Tx descripors: q0=532 o Loading network interface(s): o eth0, ifindex = 1, GbE port = 1 o Loading Gateway interface(s): o Using default network configuration, overriding boot MAC address o MTU set to 1500. o mac_addr 00:00:00:00:00:00, VID 0x100, port list: port-0 port-1 port-2 o eth1, ifindex = 2, GbE port = 0 mvFpRuleDb (cfdae000): 2048 entries, 8192 bytes e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI e100: Copyright(c) 1999-2006 Intel Corporation PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 Integrated Sata device found scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter scsi 0:0:0:0: Direct-Access SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5 Disk topology: host_no=0 channel=0 id=0 sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: [sda] Attached SCSI disk sd 0:0:0:0: Attached scsi generic sg0 type 0 NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 112 at 0x00e00000 Using static partition definition Creating 4 MTD partitions on "nand_mtd": 0x00000000-0x00100000 : "u-boot" 0x00100000-0x00400000 : "uImage" 0x00400000-0x00800000 : "uInitrd_m" 0x00800000-0x08000000 : "root" ehci_marvell ehci_marvell.70059: Marvell Orion EHCI ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usb 1-1: new high speed USB device using ehci_marvell and address 2 usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 3 ports detected usbcore: registered new interface driver usblp /home/emmanuel/workspace/wirelessspace-RC/components/kernel/source/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice input: gpio-keys as /class/input/input0 i2c /dev entries driver at24 0-0050: 512 byte 24c04 EEPROM (writable) md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 raid6: int32x1 73 MB/s raid6: int32x2 80 MB/s raid6: int32x4 83 MB/s raid6: int32x8 75 MB/s raid6: using algorithm int32x4 (83 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: measuring checksumming speed arm4regs : 726.400 MB/sec 8regs : 505.600 MB/sec 32regs : 603.200 MB/sec raid5: using function: arm4regs (726.400 MB/sec) device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com dm_crypt using the OCF package. u32 classifier Performance counters on Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (2048 buckets, 16384 max) ctnetlink v0.93: registering with nfnetlink. ip_tables: (C) 2000-2006 Netfilter Core Team arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> mv_rtc mv_rtc: setting the system clock to 2012-09-24 17:13:24 (1348506804) md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: squashfs filesystem found at block 0 RAMDISK: Loading 3139KiB [1 disk] into ram disk... done. VFS: Mounted root (squashfs filesystem) readonly. date seems valid: 2012-09-24 17:13:24 * Mounting base stuff * kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. * copyCheck is not there, checking bootcheck* * Bootcheck not there , everything is fine * Hdd seems sane... *Checking if a new firmware is there * Mount /proc... * Mount /tmp... * Create /tmp/sda4... * Mount /dev/sda4... XFS mounting filesystem sda4 * Unmount all... * Done. <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< No update found, boot from HDD... <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< start flashing blue led pivoting *Done* kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Trying to move old root to /initrd ... okay Freeing init memory: 144K INIT: version 2.86 booting Unmount old /proc Unmount old /initrd Mounting tmp /etc... Populate /etc... Mounting all... Mounting /dev/sda3 on /lacie/var kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda3, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. Mounting /dev/sda4 on /lacie/var/userPart FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! XFS mounting filesystem sda4 Creating new /var into hdd... EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS on sda1, internal journal Adding 249992k swap on /dev/sda2. Priority:-1 extents:1 across:249992k Populating /var... Done. INIT: Entering runlevel: 2 [Lo] mounting loopback interface ** Checking shares ** rmdir: '/lacie/share/inne': Directory not empty rmdir: '/lacie/share/media': Not a directory rmdir: '/lacie/share/transmission_web': Directory not empty ** Shares checked ** [udevd] starting kernel event manager udev: starting version 139 [udevd] loading hardware drivers ** hwClock ** Set system date from RTC HW clock Mon Sep 24 19:13:29 CEST 2012 [klaxon] starting [klaxon] running from HDD eth0: started eth0: stopped mv_gateway: starting eth1 mv_gateway: stopping eth1 rt3090sta: module license 'unspecified' taints kernel. === pAd = d08d1000, size = 507432 === <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xd08c0000, csr_addr=0xd08c0000! RX DESC ff019000 size = 2048 <-- RTMPAllocTxRxRingMemory, Status=0 Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 9 2. Phy Mode = 9 NVM is Efuse and its size =2d[2d0-2fc] RTMPSetPhyMode: channel is out of range, use first channel=1 Read EEPROM, EthCloneMac is ---mac---! 3. Phy Mode = 9 MCS Set = ff ff 00 00 01 <==== rt28xx_init, Status=0 0x1300 = 00064300 AUX_CTRL = 0x c02 Read AUX_CTRL = 0xc02 Write AUX_CTRL = 0x1c02 OSC_CTRL = 0x3ff11 ====> rt30xx Read PowerLevelMode = 0x3. ====> rt30xx F Write 0x83 Command = 0x3. mv_gateway: eth1 change mac address to --mac-- mv_gateway: starting eth1 device eth1 entered promiscuous mode acm_msg> ACM_MEM_Alloc_Num = 1 acm_msg> ACM_MEM_Free_Num = 1 rt28xx_close call RT28xxPciAsicRadioOff fail !! device ra0 entered promiscuous mode RX DESC ff019000 size = 2048 <-- RTMPAllocTxRxRingMemory, Status=0 CfgSetCountryRegion():CountryRegion in eeprom was programmed CfgSetCountryRegion():CountryRegion in eeprom was programmed Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 9 2. Phy Mode = 9 NVM is Efuse and its size =2d[2d0-2fc] RTMPSetPhyMode: channel is out of range, use first channel=1 3. Phy Mode = 9 MCS Set = ff ff 00 00 01 <==== rt28xx_init, Status=0 0x1300 = 00064300 AUX_CTRL = 0x 1d42 Read AUX_CTRL = 0x1d42 Write AUX_CTRL = 0x1d42 OSC_CTRL = 0x3ff11 ====> rt30xx Read PowerLevelMode = 0x3. ====> rt30xx F Write 0x83 Command = 0x3. br_wan: port 2(ra0) entering learning state br_wan: port 1(eth1) entering learning state br_wan: topology change detected, propagating br_wan: port 2(ra0) entering forwarding state br_wan: topology change detected, propagating br_wan: port 1(eth1) entering forwarding state eth0: mac address changed eth0: started WARNING: at /home/emmanuel/workspace/wirelessspace-RC/components/kernel/source/kernel/softirq.c:138 local_bh_enable() [<c0116890>] (dump_stack+0x0/0x14) from [<c0163974>] (local_bh_enable+0x40/0xb0) [<c0163934>] (local_bh_enable+0x0/0xb0) from [<bf0bd1c8>] (RtmpAsicSendCommandToMcu+0x114/0x4d0 [rt3090sta]) r5:d08d1000 r4:000b0100 [<bf0bd0b4>] (RtmpAsicSendCommandToMcu+0x0/0x4d0 [rt3090sta]) from [<bf03e024>] (AsicSendCommandToMcu+0x28/0x34 [rt3090sta]) [<bf03dffc>] (AsicSendCommandToMcu+0x0/0x34 [rt3090sta]) from [<bf04910c>] (AsicAdjustTxPower+0x2b8/0x1c80 [rt3090sta]) [<bf048e54>] (AsicAdjustTxPower+0x0/0x1c80 [rt3090sta]) from [<bf00e6f4>] (STAMlmePeriodicExec+0x3c8/0xda4 [rt3090sta]) [<bf00e32c>] (STAMlmePeriodicExec+0x0/0xda4 [rt3090sta]) from [<bf00f668>] (MlmePeriodicExec+0x598/0x734 [rt3090sta]) [<bf00f0d0>] (MlmePeriodicExec+0x0/0x734 [rt3090sta]) from [<bf039b34>] (rtmp_timer_MlmePeriodicExec+0x24/0x40 [rt3090sta]) r6:bf039b10 r5:00000100 r4:d08e9e9c [<bf039b10>] (rtmp_timer_MlmePeriodicExec+0x0/0x40 [rt3090sta]) from [<c016731c>] (run_timer_softirq+0x150/0x1e8) r5:00000100 r4:c04c4d40 [<c01671cc>] (run_timer_softirq+0x0/0x1e8) from [<c01636c0>] (__do_softirq+0x74/0xec) r7:123196a6 r6:00000002 r5:c04c4ae8 r4:00000001 [<c016364c>] (__do_softirq+0x0/0xec) from [<c0163a94>] (irq_exit+0x48/0x50) r7:123196a6 r6:00000000 r5:c049eb50 r4:00000001 [<c0163a4c>] (irq_exit+0x0/0x50) from [<c002c048>] (__exception_text_start+0x48/0x60) [<c002c000>] (__exception_text_start+0x0/0x60) from [<c002c564>] (__irq_usr+0x44/0xa0) Exception stack(0xce78ffb0 to 0xce78fff8) ffa0: 36363636 36363636 6e0740b3 1e3111a6 ffc0: 36363636 7c36d615 36363636 123196a6 36363636 f22fe673 50307191 beb22764 ffe0: 5a827999 beb225e0 fc8bf99c 0005df48 00000010 ffffffff r7:123196a6 r6:0000001e r5:f1020200 r4:ffffffff ===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 130 ==>rt_ioctl_siwfreq::SIOCSIWFREQ[cmd=0x8b04] (Channel=1) Rcv Wcid(1) AddBAReq Start Seq = 00000000 Syslogd Started [thumbd] Starting application Segmentation fault using old certificate Starting setup server setup is disabled * bootcheck * wshd login: >> smart_spindown start - disk(s): sda wshd login:
This category currently contains no pages or media.