Category:Wireless Space

From NAS-Central Lacie Wiki
Jump to: navigation, search
Network Space.jpg
Wireless Space
CPU SoC Marvell 88F6281
RAM 256MB
Flash ROM 128MB
Other
NIC
USB
internal HDD Samsung HD103SI on 1TB version
SATA Controller
Drive Capacity 1TB or 2TB
Fan
Kernel 2.6.22.18

Links

Firmware updates: http://www.lacie.com/support/support_manifest.htm?id=10520
GPL source code: http://www.lacie.com/gpl
SoC data sheets: http://www.marvell.com/products/processors/embedded/kirkwood
lacie-nas project: http://lacie-nas.org

uname -a

Linux WirelessSpace 2.6.22.18 #1 Fri Aug 20 09:20:02 CEST 2010 armv5tejl unknown

cat /proc/cpuinfo

Processor       : ARM926EJ-S rev 1 (v5l)
BogoMIPS        : 799.53
Features        : swp half thumb fastmult edsp
CPU implementer : 0x56
CPU architecture: 5TE
CPU variant     : 0x2
CPU part        : 0x131
CPU revision    : 1
Cache type      : write-back
Cache clean     : cp15 c7 ops
Cache lockdown  : format C
Cache format    : Harvard
I size          : 16384
I assoc         : 4
I line length   : 32
I sets          : 128
D size          : 16384
D assoc         : 4
D line length   : 32
D sets          : 128

Hardware        : wireless_space
Revision        : 0000
Serial          : 0000000000000000

cat /proc/meminfo

MemTotal:       254988 kB
MemFree:          3684 kB
Buffers:          8716 kB
Cached:         212236 kB
SwapCached:         88 kB
Active:         108072 kB
Inactive:       122700 kB
SwapTotal:      249992 kB
SwapFree:       249436 kB
Dirty:             456 kB
Writeback:           0 kB
AnonPages:        9760 kB
Mapped:          12136 kB
Slab:            15556 kB
SReclaimable:     1920 kB
SUnreclaim:      13636 kB
PageTables:        724 kB
NFS_Unstable:        0 kB
Bounce:              0 kB
CommitLimit:    377484 kB
Committed_AS:   124728 kB
VmallocTotal:   385024 kB
VmallocUsed:      1316 kB
VmallocChunk:   383692 kB

cat /proc/partitions

major minor  #blocks  name

   8     0  976762584 sda
   8     1     292952 sda1
   8     2     250000 sda2
   8     3      97656 sda3
   8     4  976121942 sda4
  31     0       1024 mtdblock0
  31     1       3072 mtdblock1
  31     2       4096 mtdblock2
  31     3     122880 mtdblock3 - about 120MB and contains orginal firmware backup in my case 1.0.2

cat /proc/mounts

rootfs / rootfs rw 0 0
/dev/root / ext3 ro,noatime,data=ordered 0 0
tmpfs /etc tmpfs rw 0 0
none /proc proc rw 0 0
none /sys sysfs rw 0 0
tmpfs /tmp tmpfs rw 0 0
/dev/sda3 /lacie/var ext3 rw,noatime,data=ordered 0 0
/dev/sda4 /lacie/var/userPart xfs rw,noatime 0 0
usbfs /proc/bus/usb usbfs rw 0 0
/dev/root /dev/.static/dev ext3 ro,noatime,data=ordered 0 0
udev /dev tmpfs rw 0 0

cat /proc/filesystems

nodev   sysfs
nodev   rootfs
nodev   bdev
nodev   proc
nodev   debugfs
nodev   sockfs
nodev   usbfs
nodev   pipefs
nodev   anon_inodefs
nodev   futexfs
nodev   tmpfs
nodev   inotifyfs
nodev   devpts
        ext3
        ext2
        squashfs
nodev   ramfs
        msdos
        vfat
        hfsplus
nodev   nfs
        ntfs
        jffs2
nodev   fuse
        fuseblk
nodev   fusectl
        xfs
nodev   rpc_pipefs
        tntfs

cat /proc/mtd

dev:    size   erasesize  name
mtd0: 00100000 00020000 "u-boot"
mtd1: 00300000 00020000 "uImage"
mtd2: 00400000 00020000 "uInitrd_m"
mtd3: 07800000 00020000 "root"


Serial console output with firmware 1.1.4

           _           ____ _
          | |    __ _ / ___(_) ___
          | |   / _` | |   | |/ _ \
          | |___ (_| | |___| |  __/
          |_____\__,_|\____|_|\___|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: ASTON_WS_GN3 LE
Hold rear button - long :  FAIL


U-Boot 1.1.4 (Feb 11 2010 - 11:04:03) Marvell version: 3.4.16  LaCie 1.4.2 256MB

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CE5E0

Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 800Mhz L2 running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz

DRAM CAS Latency = 6 tRP = 3 tRAS = 9 tRCD=3
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Flash:  0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 0 is MII

USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Net:   egiga0 [PRIME], egiga1
Waiting for LUMP (3)
no lump receive; continuing
Hit any key to stop autoboot:  0

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode
  Device 0 @ 0 0:
Model: SAMSUNG HD103SI                          Firm: 1AG01118 Ser#: ---removed---     
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)

## Valid EFI partition found ##
## Valid EFI partition found ##

2440768 bytes read

## Checking Image at 00800000 ...
   Image Name:   Linux-2.6.22.18
   Created:      2011-08-29  11:01:29 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2440704 Bytes =  2.3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
Kernel IDE success
## Valid EFI partition found ##
## Valid EFI partition found ##

3215424 bytes read

## Checking Image at 01200000 ...
   Image Name:   8M_ramdisk
   Created:      2011-08-29  11:32:42 UTC
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    3215360 Bytes =  3.1 MB
   Load Address: 01200000
   Entry Point:  01200000
   Verifying Checksum ... OK
IinitRD IDE success
## Booting image at 00800000 ...
   Image Name:   Linux-2.6.22.18
   Created:      2011-08-29  11:01:29 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2440704 Bytes =  2.3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 01200000 ...
   Image Name:   8M_ramdisk
   Created:      2011-08-29  11:32:42 UTC
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    3215360 Bytes =  3.1 MB
   Load Address: 01200000
   Entry Point:  01200000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux.......................................................................................................................................................... done, booting the kernel.
Linux version 2.6.22.18 (root@ws32.lacie.com) (gcc version 4.2.1) #1 Mon Aug 29 11:01:15 UTC 2011
CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
Machine: wireless_space
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists.  Total pages: 65024
Kernel command line: initrd=0x1200000 root=/dev/mtdblock3 ro console=ttyS0,115200
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB 0MB 0MB 0MB = 256MB total
Memory: 251648KB available (4504K code, 300K data, 144K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e8000000, size 128MB
PEX0_IO ....base f2000000, size   1MB
INTER_REGS ....base f1000000, size   1MB
NFLASH_CS ....base fa000000, size   2MB
SPI_CS ....base f4000000, size  16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size   2MB

  Marvell Development Board (LSP Version KW_LSP_4.2.7_patch2)-- wireless_space  Soc: MV88F6281 Rev 3 LE

 Detected Tclk 166666667 and SysClk 200000000
MV Buttons Device Load
Register Marvell USB EHCI Host controller #0
PEX0 interface detected Link X1
PCI: bus0: Fast back to back transfers disabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: kw_clocksource clocksource has been installed.
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 3140K
Use the XOR engines (acceleration) for enhancing the following functions:
  o RAID 5 Xor calculation
  o kernel memcpy
  o kenrel memzero
Number of XOR engines to use: 2
cesadev_init(c00118ac)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
MV Buttons Driver Load
mv_rtc mv_rtc: rtc core: registered mv_rtc as rtc0
mv_rtc mv_rtc: Kirkwood SoC RTC added
Init kirkwood cpufreq driver
gpio-fan gpio-fan: GPIO fan initialized
gpio-hd-power gpio-hd-power: GPIO Hard Disk power device initialized
gpio-usb gpio-usb: GPIO USB mode switch is not available
gpio-usb gpio-usb: GPIO USB device VBUS is not available
gpio-usb gpio-usb: USB GPIO's initialized
Registered led device: ws:red:front
Registered led device: ws:green:front
Registered led device: ws:blue:front
squashfs: version 3.3 (2007/10/31) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
NTFS driver 2.1.28 [Flags: R/O].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.8)
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
INIT Marvell Ethernet Driver: mv_netdev
Loading Marvell Ethernet Driver:
  o Cached descriptors in DRAM
  o DRAM SW cache-coherency
  o Single RX Queue support - ETH_DEF_RXQ=0
  o Single TX Queue support - ETH_DEF_TXQ=0
  o TCP segmentation offload enabled
  o Receive checksum offload enabled
  o Transmit checksum offload enabled
  o Network Fast Processing (Routing) supported
  o Driver ERROR statistics enabled
  o Driver INFO statistics enabled
  o Driver DEBUG statistics enabled
  o Proc tool API enabled
  o Gateway support enabled
     o Using Marvell Header Mode
     o L2 IGMP support
  o Rx descripors: q0=128
  o Tx descripors: q0=532
  o Loading network interface(s):
    o eth0, ifindex = 1, GbE port = 1
  o Loading Gateway interface(s):
      o Using default network configuration, overriding boot MAC address
      o MTU set to 1500.
      o mac_addr 00:00:00:00:00:00, VID 0x100, port list: port-0 port-1 port-2
    o eth1, ifindex = 2, GbE port = 0

mvFpRuleDb (cfdae000): 2048 entries, 8192 bytes
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Integrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access     SAMSUNG  HD103SI          1AG0 PQ: 0 ANSI: 5
Disk topology: host_no=0 channel=0 id=0
sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] 1953525168 512-byte hardware sectors (1000205 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 112 at 0x00e00000
Using static partition definition
Creating 4 MTD partitions on "nand_mtd":
0x00000000-0x00100000 : "u-boot"
0x00100000-0x00400000 : "uImage"
0x00400000-0x00800000 : "uInitrd_m"
0x00800000-0x08000000 : "root"
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
usb 1-1: new high speed USB device using ehci_marvell and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 3 ports detected
usbcore: registered new interface driver usblp
/home/emmanuel/workspace/wirelessspace-RC/components/kernel/source/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
input: gpio-keys as /class/input/input0
i2c /dev entries driver
at24 0-0050: 512 byte 24c04 EEPROM (writable)
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1     73 MB/s
raid6: int32x2     80 MB/s
raid6: int32x4     83 MB/s
raid6: int32x8     75 MB/s
raid6: using algorithm int32x4 (83 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
   arm4regs  :   726.400 MB/sec
   8regs     :   505.600 MB/sec
   32regs    :   603.200 MB/sec
raid5: using function: arm4regs (726.400 MB/sec)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
u32 classifier
    Performance counters on
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2048 buckets, 16384 max)
ctnetlink v0.93: registering with nfnetlink.
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
mv_rtc mv_rtc: setting the system clock to 2012-09-24 17:13:24 (1348506804)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: squashfs filesystem found at block 0
RAMDISK: Loading 3139KiB [1 disk] into ram disk... done.
VFS: Mounted root (squashfs filesystem) readonly.
date seems valid: 2012-09-24 17:13:24
* Mounting base stuff *
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
* copyCheck is not there, checking bootcheck*
* Bootcheck not there , everything is fine *
Hdd seems sane...
*Checking if a new firmware is there
 * Mount /proc...
 * Mount /tmp...
 * Create /tmp/sda4...
 * Mount /dev/sda4...
XFS mounting filesystem sda4
* Unmount all...
 * Done.
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
No update found, boot from  HDD...
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
start flashing blue led
pivoting
*Done*
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... okay
Freeing init memory: 144K
INIT: version 2.86 booting
Unmount old /proc
Unmount old /initrd
Mounting tmp /etc...
Populate /etc...
Mounting all...
Mounting /dev/sda3 on /lacie/var
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda3, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Mounting /dev/sda4 on /lacie/var/userPart
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
XFS mounting filesystem sda4
Creating new /var into hdd...
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda1, internal journal
Adding 249992k swap on /dev/sda2.  Priority:-1 extents:1 across:249992k
Populating /var...
Done.
INIT: Entering runlevel: 2
[Lo] mounting loopback interface
** Checking shares **
rmdir: '/lacie/share/inne': Directory not empty
rmdir: '/lacie/share/media': Not a directory
rmdir: '/lacie/share/transmission_web': Directory not empty
** Shares checked **
[udevd] starting kernel event manager
udev: starting version 139
[udevd] loading hardware drivers
** hwClock **
Set system date from RTC HW clock
Mon Sep 24 19:13:29 CEST 2012
[klaxon] starting
[klaxon] running from HDD
eth0: started
eth0: stopped
mv_gateway: starting eth1
mv_gateway: stopping eth1
rt3090sta: module license 'unspecified' taints kernel.


=== pAd = d08d1000, size = 507432 ===

<-- RTMPAllocAdapterBlock, Status=0
pAd->CSRBaseAddress =0xd08c0000, csr_addr=0xd08c0000!
RX DESC ff019000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
NVM is Efuse and its size =2d[2d0-2fc]
RTMPSetPhyMode: channel is out of range, use first channel=1
Read EEPROM, EthCloneMac is ---mac---!
3. Phy Mode = 9
MCS Set = ff ff 00 00 01
<==== rt28xx_init, Status=0
0x1300 = 00064300
 AUX_CTRL = 0x                             c02
 Read AUX_CTRL = 0xc02
 Write AUX_CTRL = 0x1c02
 OSC_CTRL = 0x3ff11
====> rt30xx Read PowerLevelMode =  0x3.
====> rt30xx F Write 0x83 Command = 0x3.
mv_gateway: eth1 change mac address to --mac--
mv_gateway: starting eth1
device eth1 entered promiscuous mode
acm_msg> ACM_MEM_Alloc_Num = 1
acm_msg> ACM_MEM_Free_Num  = 1
rt28xx_close call RT28xxPciAsicRadioOff fail !!
device ra0 entered promiscuous mode
RX DESC ff019000  size = 2048
<-- RTMPAllocTxRxRingMemory, Status=0
CfgSetCountryRegion():CountryRegion in eeprom was programmed
CfgSetCountryRegion():CountryRegion in eeprom was programmed
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 9
2. Phy Mode = 9
NVM is Efuse and its size =2d[2d0-2fc]
RTMPSetPhyMode: channel is out of range, use first channel=1
3. Phy Mode = 9
MCS Set = ff ff 00 00 01
<==== rt28xx_init, Status=0
0x1300 = 00064300
 AUX_CTRL = 0x                            1d42
 Read AUX_CTRL = 0x1d42
 Write AUX_CTRL = 0x1d42
 OSC_CTRL = 0x3ff11
====> rt30xx Read PowerLevelMode =  0x3.
====> rt30xx F Write 0x83 Command = 0x3.
br_wan: port 2(ra0) entering learning state
br_wan: port 1(eth1) entering learning state
br_wan: topology change detected, propagating
br_wan: port 2(ra0) entering forwarding state
br_wan: topology change detected, propagating
br_wan: port 1(eth1) entering forwarding state
eth0: mac address changed
eth0: started
WARNING: at /home/emmanuel/workspace/wirelessspace-RC/components/kernel/source/kernel/softirq.c:138 local_bh_enable()
[<c0116890>] (dump_stack+0x0/0x14) from [<c0163974>] (local_bh_enable+0x40/0xb0)
[<c0163934>] (local_bh_enable+0x0/0xb0) from [<bf0bd1c8>] (RtmpAsicSendCommandToMcu+0x114/0x4d0 [rt3090sta])
 r5:d08d1000 r4:000b0100
[<bf0bd0b4>] (RtmpAsicSendCommandToMcu+0x0/0x4d0 [rt3090sta]) from [<bf03e024>] (AsicSendCommandToMcu+0x28/0x34 [rt3090sta])
[<bf03dffc>] (AsicSendCommandToMcu+0x0/0x34 [rt3090sta]) from [<bf04910c>] (AsicAdjustTxPower+0x2b8/0x1c80 [rt3090sta])
[<bf048e54>] (AsicAdjustTxPower+0x0/0x1c80 [rt3090sta]) from [<bf00e6f4>] (STAMlmePeriodicExec+0x3c8/0xda4 [rt3090sta])
[<bf00e32c>] (STAMlmePeriodicExec+0x0/0xda4 [rt3090sta]) from [<bf00f668>] (MlmePeriodicExec+0x598/0x734 [rt3090sta])
[<bf00f0d0>] (MlmePeriodicExec+0x0/0x734 [rt3090sta]) from [<bf039b34>] (rtmp_timer_MlmePeriodicExec+0x24/0x40 [rt3090sta])
 r6:bf039b10 r5:00000100 r4:d08e9e9c
[<bf039b10>] (rtmp_timer_MlmePeriodicExec+0x0/0x40 [rt3090sta]) from [<c016731c>] (run_timer_softirq+0x150/0x1e8)
 r5:00000100 r4:c04c4d40
[<c01671cc>] (run_timer_softirq+0x0/0x1e8) from [<c01636c0>] (__do_softirq+0x74/0xec)
 r7:123196a6 r6:00000002 r5:c04c4ae8 r4:00000001
[<c016364c>] (__do_softirq+0x0/0xec) from [<c0163a94>] (irq_exit+0x48/0x50)
 r7:123196a6 r6:00000000 r5:c049eb50 r4:00000001
[<c0163a4c>] (irq_exit+0x0/0x50) from [<c002c048>] (__exception_text_start+0x48/0x60)
[<c002c000>] (__exception_text_start+0x0/0x60) from [<c002c564>] (__irq_usr+0x44/0xa0)
Exception stack(0xce78ffb0 to 0xce78fff8)
ffa0:                                     36363636 36363636 6e0740b3 1e3111a6
ffc0: 36363636 7c36d615 36363636 123196a6 36363636 f22fe673 50307191 beb22764
ffe0: 5a827999 beb225e0 fc8bf99c 0005df48 00000010 ffffffff
 r7:123196a6 r6:0000001e r5:f1020200 r4:ffffffff
===>rt_ioctl_giwscan. 1(1) BSS returned, data->length = 130
==>rt_ioctl_siwfreq::SIOCSIWFREQ[cmd=0x8b04] (Channel=1)
Rcv Wcid(1) AddBAReq
Start Seq = 00000000
Syslogd Started
[thumbd] Starting application
Segmentation fault
using old certificate
Starting setup server
  setup is disabled
* bootcheck *

wshd login: >> smart_spindown start - disk(s):  sda

wshd login:

This category currently contains no pages or media.